 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MITSUMI Video Switch * 75 driver * Y/C mix MM1501 Video Switch * 75 driver * Y/C mix Monolithic IC MM1501 Series Outline This IC extends the series of ICs for video/audio signal switching, with a 2-input 1-output single video switch, video signal/chroma signal 75 driver, and Y/C mixing circuit in one small package (SOT-26). Features (1) Low power consumption achieved. (2) Low power supply voltage realized. (3) Frequency bandwidth without 75 driver: 10MHz (4) Cross talk 70dB When 4.43MHz (5) With SAG measures pin (75 driver and Y/C mix driver) with 75 driver: 7MHz Package SOT-26A (with 75 driver) SOT-26B (without 75 driver) Applications (1) TV (2) VTR (3) Video camera (4) Digital still camera (5) Other visual equipment Line-up Functions Model Name Input Output MM1501 MM1502 MM1503 MM1504 MM1505 MM1506 MM1507 MM1508 MM1509 MM1510 MM1511 MM1512 Clamp 6dB amp 75 driver SAG measures pin Power supply voltage 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V 4.5~13.0V Switch 2 1 Driver Y/C mix 1 1 1 1 / / MITSUMI Video Switch * 75 driver * Y/C mix MM1501 Block Diagram MM1501 MM1502 MM1503 MM1504 MM1505 MM1506 MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1507 MM1508 MM1509 MM1510 MM1511 MM1512 MITSUMI Video Switch * 75 driver * Y/C mix MM1501 Absolute Maximum Ratings (Ta=25C) Item Storage temperature Operating temperature Power supply voltage When alone Allowable loss When mounted on board Symbol TSTG TOPR VCC Pd Pd Rating Unit -40~+125 C -30~+75 C 15 V 200 mW 350 ( ) mW Board size 100mm 100mm t=1.6 * Recommended Operating Conditions Item Power supply voltage Symbol VCC * Rating 4.5~13 Unit V Electrical Characteristics MM1501 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain VCC=9V Differential phase VCC=9V Total harmonic distortion ratio Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Input impedance Output impedance (Except where noted otherwise, Ta=25C, VCC=5V) Symbol ICC VIN VOUT GV fc DG DP THD VD VOFF CT VIH VIL Zi Zo Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 3.7 4.8 mA 2.70 2.90 3.10 V 2.15 V -0.5 0 +0.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 0.03 0.3 % 3.5 3.8 V 15 mV -70 -60 dB 2.1 V 0.7 V 15 k 75 MM1502 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain VCC=9V Differential phase VCC=9V Total harmonic distortion ratio Output dynamic range Output offset voltage Cross talk SW input voltage H Sw input voltage L Input impedance Output impedance Symbol ICC VIN VOUT GV fc DG DP THD VD VOFF CT VIH VIL Zi Zo Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 4.7 6.1 mA 1.70 1.90 2.10 V 2.10 V 5.5 6.0 6.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 0.03 0.3 % 3.5 3.8 V 30 mV -70 -60 dB 2.1 V 0.7 V 15 k 12 MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1503 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain Differential phase Total harmonic distortion ratio Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Input impedance Symbol ICC VIN VOUT GV fc DG DP THD VD VOFF CT VIH VIL Zo Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 3.3 4.3 mA 1.80 2.00 2.20 V 1.25 V -0.5 0 +0.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 0.03 0.3 % 2.6 2.9 V 15 mV -70 -60 dB 2.1 V 0.7 V 75 MM1504 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain Differential phase Total harmonic distortion ratio Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Input impedance Symbol ICC VIN VOUT GV fc DG DP THD VD VOFF CT VIH VIL Zo Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 4.4 5.7 mA 1.20 1.40 1.60 V 1.25 V 5.5 6.0 6.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 0.03 0.3 % 2.6 2.9 V 30 mV -70 -60 dB 2.1 V 0.7 V 12 MM1505 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain VCC=9V Differential phase VCC=9V Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Input impedance Symbol ICC VIN VOUT GV fc DG DP VD VOFF CT VIH VIL Zi Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 6.5 8.5 mA 2.35 2.55 2.75 V 2.55 V -0.5 0.0 0.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 2.6 3.0 V 15 mV -70 -60 dB 2.1 V 0.7 V 15 k MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1506 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain VCC=9V Differential phase VCC=9V Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Input impedance Symbol ICC VIN VOUT GV fc DG DP VD VOFF CT VIH VIL Zi Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 6.8 8.8 mA 1.75 1.95 2.15 V 2.35 V 5.5 6.0 6.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 3.0 3.3 V 30 mV -70 -60 dB 2.1 V 0.7 V 15 k MM1507 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain Differential phase Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Symbol ICC VIN VOUT GV fc DG DP VD VOFF CT VIH VIL Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 6.4 8.3 mA 1.15 1.35 1.55 V 1.35 V -0.5 0 +0.5 dB -1 0 +1 dB 0 +3 % -3 -3 0 +3 deg 2.6 2.9 V 15 mV -70 -60 dB 2.1 V 0.7 V MM1508 Item Consumption current Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain Differential phase Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Symbol ICC VIN VOUT GV fc DG DP VD VOFF CT VIH VIL Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 6.8 8.8 mA 1.15 1.35 1.55 V 1.30 V 5.5 6.0 6.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 2.6 3.0 V 30 mV -70 -60 dB 2.1 V 0.7 V MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1509 Item Consumption current Current consumption for PS PS input voltage L PS input voltage H Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain VCC=9V Differential phase VCC=9V Output dynamic range Input impedance Symbol ICC1 ICC2 VPSL VPSH VIN VOUT GV fc DG DP VD Zi Measurement conditions Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 6.3 8.2 mA 20 30 A 0.3 V 1.8 V 1.75 1.95 2.15 V 2.35 V 5.5 6.0 6.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 2.9 3.2 V 15 k MM1510 Item Consumption current Current consumption for PS PS input voltage L PS input voltage H Input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain Differential phase Output dynamic range Symbol ICC1 ICC2 VPSL VPSH VIN VOUT GV fc DG DP VD Measurement conditions Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 6.4 8.3 mA 20 30 A 0.3 V 1.8 V 1.15 1.35 1.55 V 1.15 V 5.5 6.0 6.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 2.6 3.0 V MM1511 Item Consumption current Y input pin voltage C input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain Differential phase Y output dynamic range C output dynamic range C input impedance Output impedance Symbol ICC VYIN VCIN VOUT GV fc DG DP VDY VDC Zi Zo Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 4.4 5.7 mA 2.00 2.20 2.40 V 1.85 2.05 2.25 V 1.15 V -0.5 0 6.5 dB -1 0 +0.5 dB -3 0 +3 % -3 0 +3 deg 2.6 2.9 V 2.0 V 15 k 25 MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1512 Item Consumption current Y input pin voltage C input pin voltage Output pin voltage Voltage gain Frequency characteristic Differential gain Differential phase Y output dynamic range C output dynamic range C input impedance Symbol ICC VYIN VCIN VOUT GV fc DG DP VDY VDC Zi Measurement conditions Refer to measurement procedures No-signal, no-load No-signal, no-load No-signal, no-load Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Refer to measurement procedures Min. Typ. Max. Unit 6.9 9.0 mA 1.95 2.15 2.35 V 1.80 2.00 2.20 V 1.10 V 5.5 6.0 6.5 dB -1 0 +1 dB -3 0 +3 % -3 0 +3 deg 2.6 2.9 V 2.0 V 15 k Measurement Procedures MM1501~MM1508 * Switch Status Item Consumption current Voltage gain Frequency characteristic Differential gain Differential phase Symbol ICC GV fc DG DP Switch status S1 S2 S3 2 2 2 1 2 2 2 1 1 1 2 2 2 1 1 1 2 2 2 1 1 1 2 2 2 1 1 Item Total harmonic distortion ratio Output dynamic range Output offset voltage Cross talk SW input voltage H SW input voltage L Symbol THD VD VOFF CT VIH VIL Switch status S1 S2 S3 1 2 2 2 1 1 1 2 2 2 1 1 2 2 2 2 2 1 1 2 1 2 1 2 2 2 1 MITSUMI Video Switch * 75 driver * Y/C mix MM1501 *Measurement Procedures (MM1501 ~ MM1504) Consumption current ICC Connect a DC ammeter to VCC pin and measure. Hereafter, short the ammeter to use. Input a 2.0VP-P (1.0VP-P for MM1502 and MM1504), 100kHz sine wave to SG1. If TP1 voltage is V1 and TP3 voltage is V2, find Gv using the following formula: GV = 20LOG (V2/V1) dB In the above Gv measurement, if TP3 voltage at 10MHz is V3, find fc as follows: fc = 20LOG (V3/V2) dB Input a 2.0VP-P (1.0VP-P for MM1502 and MM1504) staircase to SG1 and measure differential gain at TP3. APL = 10 ~ 90% The same as for DG, but measure differential phase. Input a 2.5VP-P (1.25VP-P for MM1502, MM1504), 1kHz sine wave to SG1, connect a distortion factor meter to TP3 and measure. Input a 100kHz sine wave to SG1. Change the amplitude of the sine wave, and measure VD, the maximum amplitude under THD 1%, at TP3. Measure the DC voltage difference of each switch status at TP2. VC1 = 2.1V and VC2 = 0.7V. Input a 2.0VP-P, 4.43MHz sine wave to SG1, and operate SW3. If TP3 voltage when there is an output signal on the OUT pin is V4, and when there is no signal TP3 voltage is V5, then find CT by the following formula: CT = 20LOG (V5/V4) dB Impress an optional DC voltage on TP5 and TP6. Gradually increase from VC1 = 0V. When TP6 voltage is output on TP2, TP4 voltage is VIH. Gradually lower from VC1 = VCC, and when TP5 voltage is output on TP2, TP4 voltage is VIL. Voltage gain GV Frequency characteristic fc Differential gain Differential phase Total harmonic distortion ratio DG DP THD Output dynamic range Output offset voltage VD VOFF Cross talk CT SW input voltage VI MITSUMI Video Switch * 75 driver * Y/C mix MM1501 * Measurement Procedures (MM1505 ~ MM1508) Consumption current ICC Connect a DC ammeter to VCC pin and measure. Hereafter, short the ammeter to use. Input a 2.0VP-P(1.0VP-P for MM1506 and MM1508), 100kHz sine wave to SG1. If TP1 voltage is V1 and TP3 voltage is V2, find GV using the following formula: GV = 20LOG (V2/V1) dB In the above GV measurement, if TP3 voltage at 7MHz is V3, find fc as follows: fc = 20LOG (V3/V2) dB Input a 2.0VP-P (1.0VP-P for MM1506 and MM1508) staircase to SG1 and measure differential gain at TP3. APL = 10 ~ 90% The same as for DG, but measure differential phase. Input a 100kHz sine wave to SG1. Change the amplitude of the sine wave, and measure VD, the maximum amplitude under THD 1%, at TP3. Measure the DC voltage difference of each switch status at TP2. VC1 = 2.1V and VC2 = 0.7V. Input a 2.0VP-P, 4.43MHz sine wave to SG1, and operate SW3. IF TP3 voltage when there is an output signal on the OUT pin is V4, and when there is no signal TP3 voltage is V5, then find CT by the following formula: CT = 20LOG (V5/V4) dB Impress an optional DC voltage on TP6 and TP7. Gradually increase from VC1 = 0V. When TP7 voltage is output on TP2, TP5 voltage is VIH. Gradually lower from VC1 = VCC, and when TP6 voltage is output on TP2, TP5 voltage is VIL. Voltage gain GV Frequency characteristic Differential gain Differential phase Output dynamic range Output offset voltage fc DG DP VD VOFF Cross talk CT SW input voltage VI MM1509 ~ MM1510 * Switch Status Item Consumption current Consumption current for PS PS input voltage L PS input voltage H Voltage gain Symbol ICC1 ICC2 VIL VIH GV Switch status S1 S2 2 1 2 3 2 1 2 1 Item Frequency characteristic Differential gain Differential phase Output dynamic range Symbol fc DG DP VD Switch status S1 S2 1 1 1 1 1 1 1 1 * Measurement Procedures Consumption current Consumption current for PS ICC1 ICC2 Connect a DC ammeter to the VCC pin and measure. Connect a DC ammeter to the VCC pin and measure. Connect a DC ammeter to the VCC pin. Gradually lower from VC1 = VCC. VC1 voltage when consumption current is reduced from ICC1 to 110% of ICC2 is VIL. Gradually raise from VC1 = 0V. VC1 voltage when consumption current increases from ICC2 to 90% of ICC1 is VIH. From here on, short the ammeter when using it. Input a 1.0VP-P, 100kHz sine wave to SG1. If TP1 voltage is V1 and TP2 voltage is V2, find GV by the following formula: GV = 20LOG (V2/V1) dB In the above GV measurement, if TP2 voltage at 7MHz is V3, find fc by the following formula. fc = 20LOG (V3/V2) dB Input a 1.0VP-P staircase to SG1 and measure differential gain at TP2. APL = 10 ~ 90% The same as for DG, but measure differential phase. Input a 100kHz sine wave to SG1. Measure DR, the maximum amplitude under THD 1%, at TP2. PS input voltage VI Voltage gain GV fc Frequency characteristic Differential gain Differential phase Output dynamic range DG DP VD MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1511 ~ MM1512 * Switch Status Item Consumption current Voltage gain Frequency characteristic Symbol ICC GV fc Switch status S1 S2 2 2 1 2 2 1 1 2 2 1 Item Differential gain Differential phase Y output dynamic range C output dynamic range Symbol DG DP VDY VDC Switch status S1 S2 3 1 3 1 2 1 3 1 * Measurement Procedures Consumption current Voltage gain ICC1 GV Connect a DC ammeter to the VCC pin and measure. Hereafter, short the ammeter to use. Input a 2.0VP-P (1.0VP-P for MM1512), 100kHz sine wave to SG1. If TP1 voltage is V1 and TP2 voltage is V2, find GV by the following formula: GV = 20LOG (V2/V1) dB In the above GV measurement, if TP2 voltage at 10MHz (7MHz for MM1512) is V3, find fc by the following formula. fc = 20LOG (V3/V2) dB Input a 2.0VP-P (1.0VP-P for MM1512) to SG1, input a chroma signal to SG2, and measure differential gain at TP2. APL = 10 ~ 90% The same as for DG, but measure differential phase. Input a 100kHz sine wave to SG1. Measure VDY, the maximum amplitude under THD 1%, at TP2. Input an APL 50% luminance signal to SG1 and input a chroma signal to SG2. Change the chroma signal amplitude and measure VDC, the maximum amplitude where there is no waveform distortion at TP2. Frequency characteristic fc Differential gain Differential phase Y output dynamic range DG DP VDY C output dynamic range VDC MITSUMI Video Switch * 75 driver * Y/C mix MM1501 Measuring Circuit MM1501 MM1502 MM1503 MM1504 MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1505 MM1506 MM1507 MM1508 MITSUMI Video Switch * 75 driver * Y/C mix MM1501 MM1509 MM1510 MM1511 MM1512 |
Price & Availability of MM1501
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |